Offer of a used machine in other presses
Table load lower table 46.000 Kg
Table load upper table 20.000 Kg
Minimum Die height 300 mm
Maximum Die height 2400 mm
Equipped with options
Tilting table 180 Gr
Electric paralel control system
X-travel lower base extensions to 2000 mm
Distance between column:2130 x 2730mm
Hight under roof: 2400mm
Table Length: 2500 x 2000mm
Ram stroke: 2100mm
Approche speed: 80mm/min.
Working speed: 8mm/min.
Return speed: 50mm/min.
Table rotation: 180U/mm
Length: 7800mm
Width: 5600mm
Height: 6510mm
Weight: 56000kg
The MiL 263 spotting presses for assembly, adjustment, check and reapir for large moulds.
This press is used for splitting, adjusting, maintenance and try-out operations
on dies and moulds (thermoplastics, die casting, thermosetting, rubber and blanking)
The lower table is build in floor pit version
The die & mould spotting presses of the traditional MIL series feature the extensible plate exit on the side, towards the short side of the distance between columns. They are typically used in the plastics, rubber and die casting sectors.This solution allows tilting on the extensible plate short side up to 70° on both sides. In this version, the upper plate, too, is tilted on the short side from 100° to 180°.
The MIL series provides great advantages compared to other solutions with long side rotation
Better working ergonomics, granting the operator to have easy access to any mould part without the use of platforms;
Much shorter total press height above ground, which often reduces excess costs for foundations;
Wide base press structure with greater stability;
The two mould-halves are located on the same side, so operators have an overview of the whole mould and can work more comfortably
www.mach4metal.com
Table load lower table 46.000 Kg
Table load upper table 20.000 Kg
Minimum Die height 300 mm
Maximum Die height 2400 mm
Equipped with options
Tilting table 180 Gr
Electric paralel control system
X-travel lower base extensions to 2000 mm
Distance between column:2130 x 2730mm
Hight under roof: 2400mm
Table Length: 2500 x 2000mm
Ram stroke: 2100mm
Approche speed: 80mm/min.
Working speed: 8mm/min.
Return speed: 50mm/min.
Table rotation: 180U/mm
Length: 7800mm
Width: 5600mm
Height: 6510mm
Weight: 56000kg
The MiL 263 spotting presses for assembly, adjustment, check and reapir for large moulds.
This press is used for splitting, adjusting, maintenance and try-out operations
on dies and moulds (thermoplastics, die casting, thermosetting, rubber and blanking)
The lower table is build in floor pit version
The die & mould spotting presses of the traditional MIL series feature the extensible plate exit on the side, towards the short side of the distance between columns. They are typically used in the plastics, rubber and die casting sectors.This solution allows tilting on the extensible plate short side up to 70° on both sides. In this version, the upper plate, too, is tilted on the short side from 100° to 180°.
The MIL series provides great advantages compared to other solutions with long side rotation
Better working ergonomics, granting the operator to have easy access to any mould part without the use of platforms;
Much shorter total press height above ground, which often reduces excess costs for foundations;
Wide base press structure with greater stability;
The two mould-halves are located on the same side, so operators have an overview of the whole mould and can work more comfortably
www.mach4metal.com
Subject to alterations and errors in the technical datas, specifications and pricing and subject to prior sale.
Short Link to this page: https://www.blechzulieferer.com/65509/offer
Vendor
Mach4Metal
Transito 21
6909 DA Babberich
(Netherlands)
Contact person: Laura Lochner
Phone: +31 (0)316-247123
Telefax: +31 (0)316-247956